Skip to Content

autocad similar command

ARC command.

The ARC command is used to create arcs.

Command Access:

Ribbon : Home > Draw> Arc
Menu : Draw > Arc
Command : ARC

Command Prompts:

Specify start point of arc or [Center]:

Function Description:

Users could create arcs by specifying combinations of center point, endpoint, start point, radius, angle, chord length, and direction.

Relative Glossary:

Start point:
Specify the start point of arc.
Note : if pressing ENTER without specifying the start point, the last endpoint of straight line or arc will become start point and prompt to specify endpoint of arc. It will create an arc that tangent to the last straight line or arc or polyline.

Second point: Create an arc by three specified points; those points are all on the same circle. The first point is start point, the third point is endpoint, and the second point is one point on circle.

arc1

Those three points could specify an arc clockwise or anticlockwise.

Center:
Specify the center of a circle; the created arc is a part of circle.

Endpoint:
Specify the center 1 and create an arc from the start point 2 to the end point 3 in anticlockwise. The end point is on an assumed ray that started from the center point to the end point, so the endpoint may be not on created arc.

arc2

Angle:
Specify the center 1 and create an arc from the start point 2 with a specified included angle. If the included angle is negative, the arc will be created in clockwise; if it is positive, the arc will be created in anticlockwise.

arc3

Chord length:
Create an arc by a specified chord length; the chord is a line segment from the start point to endpoint of arc. If specifying the chord length to a positive value, it will create a minor arc from the start point in anticlockwise direction; if specifying a negative value, it will create a major arc in anticlockwise direction

arc4

End:

Specify the endpoint of an arc.

Center:
Create an arc from start point to endpoint in anticlockwise direction. The end point is on an assumed ray that started from center point to the second specified point.

arc5

Angle:
Create an arc with a specified angle from start point to endpoint. If the inputted angle is negative, the arc will be created in clockwise direction.

arc6

Direction:
Create an arc from start point to endpoint and specify the tangent line direction of the start point. Users only need to determine tangency direction without regard to anticlockwise or clockwise, major arc or minor arc.

Center:
Specify the center of an arc.

Endpoint:
The point 1 is center of arc. The arc is from the point 2 to point 3. It is created in anticlockwise. The point 3 is located on the assumed line from center point 1 to point 3.

arc7

Radius:
Create a minor arc from the start point to end point. If inputting a negative value for radius, it will create a major

 arc8

Center:
Specify the center of an arc.

Endpoint:
The point 1 is center of arc. The arc is from the point 2 to point 3. It is created in anticlockwise. The point 3 is located on the assumed line from center point 1 to point 3.

 arc9

Angle:
The point 1 is center of arc. The included angle is from the point 2. It is created in anticlockwise. If inputting a negative angle, the arc will be created in clockwise direction.

arc10

Chord length:
The point 1 is center of arc. The chord length is the distance from the point 2 to the endpoint. Users could create a major arc or minor arc by specied chord length. If inputting a positive chord length value, it will create a minor arc in anticlockwise; if inputting a negative chord length value, it will create a major arc in anticlockwise.

arc11

 

 

 


Related tutorial video:

 

 

 


 

 

Above video sources from TUTORIAL - GETTING STARTED WITH GSTARCAD, enrol now for free.

 


 

 

Above video sources from TUTORIAL - GETTING STARTED WITH GSTARCAD, enrol now for free.

 

 

gstarcad

gstarcad

gstarcad

gstarcad